Last reviewed:

DTM CONTROL 4G user manual

The DTM CONTROL 4G is a 2/4-channel GSM receiver by DTM System for gates and other automation, on 4G and 2G networks. A stored number opens a channel with a call: the receiver ends the call and switches the channel, and the manual says this connection is free (page 29). It also takes SMS commands (manual pages 3 and 29). This page gives its specifications and SMS commands, each with the page of the manual it comes from.

Status in the GateOpener app: The app does not support this module yet.

Download the manuals

The manufacturer's PDFs, as published:

Specifications

ItemValue and source
Default configuration passwordadmin, until the first administrator is added Source: CONTROL 4G manual 1.0, pages 9 and 10
Phone numbers stored4,000, including 1 super administrator and 4 administrators Source: CONTROL 4G manual 1.0, page 3
Relay outputs2, NO or NC, 1 A at 24 V AC or DC Source: CONTROL 4G manual 1.0, page 3
Radio channels2 more with the optional 2CS (433 MHz) or 2CS868 (868 MHz) module Source: CONTROL 4G manual 1.0, pages 3 and 8
Information inputs3, NO or NC Source: CONTROL 4G manual 1.0, page 3
Output modesMonostable, 1 to 65,535 s (call or SMS), or bistable (SMS only) Source: CONTROL 4G manual 1.0, pages 3 and 8
Power supply12 to 24 V AC/DC ±10%, 500 mA Source: CONTROL 4G manual 1.0, page 3
Mobile network4G and 2G; 700, 800, 900, 1800, 2100 and 2600 MHz Source: CONTROL 4G manual 1.0, page 3
SIM cardNano SIM, PIN off, voicemail off Source: CONTROL 4G manual 1.0, page 6
Operating temperature-20 to +55 °C Source: CONTROL 4G manual 1.0, page 3
Housing / boardIP-54, 72 x 132 x 41 mm / 58 x 88 x 27 mm Source: CONTROL 4G manual 1.0, page 3

DTM also configures the receiver with its MEMO service programmer and MEMO MANAGER program for Windows, and with its own Android apps (manual pages 3 and 9).

To reset it to the factory settings, hold the RESET button on the board for 8 seconds. This deletes every stored number (manual page 8).

SMS commands from the manual

A configuration SMS starts with # and the password, then parameter=value pairs separated by commas: #password,sms1=1,clip1=0,time1=30. Parameter names may be upper or lower case; the password is case-sensitive (manual page 10).

Until an administrator is added, the password is admin and any number can configure the receiver. After that, only an administrator's number can (manual page 10). Most of the manual's examples below write #password: put your own password there (manual page 10).

Control SMS (OUTn, STATUS, GETCONFIG) need no # and no password, unless an SMS password is set: then the password and a dot come first (manual page 30). Write phone numbers with the country code, as +48123456789 or 0048123456789: a number without it is accepted but never recognised (manual pages 16 and 30).

Add an administrator (first one with the default password)

Adds a number with administrator rights and sets its configuration password (up to 16 letters and digits, case-sensitive). The SMS starts with #<password>, as every configuration SMS; until an administrator exists the password is admin. The first administrator must be the sender's own number (else ERROR: Set yourself as an admin first) and becomes super administrator. At most 5 administrators in all. Add CLIPn=1 to the same SMS to let the administrator open channel n by call: ADD switches off every right it does not name.

Syntax: ADD={phone},VIP="{newpwd}"
In the manual: ADD=user_number,VIP="password"
Reply: SUCCESSFULLY ADDED, or OK (n params); ERROR: Set yourself as an admin first; ERROR: No more VIP available
The manual prints this line without "#password," (page 10). Every configuration SMS starts with it: the manual's example on that page begins "# admin, ADD = 48123456789".
Source: CONTROL 4G manual 1.0, page 10

Give a stored user administrator rights

Makes a stored user an administrator with his own configuration password.

Syntax: #{pwd},MOD={phone},VIP="{newpwd}"
In the manual: #password,MOD=48123456789,VIP="stefek70"
Reply: SUCCESSFULLY MODIFIED, or OK (n params); ERROR: No more VIP available; ERROR: Does not exist
Source: CONTROL 4G manual 1.0, page 17

Remove administrator rights

The number stays stored as a subscriber. An administrator cannot remove his own rights; the super administrator cannot be modified by an administrator.

Syntax: #{pwd},MOD={phone},VIP=""
In the manual: #stefek70,MOD=48987654321,VIP=""
Reply: SUCCESSFULLY MODIFIED, or OK (n params); ERROR: Currently, you can not delete / modify yourself. Try from another admin; ERROR: You can not delete / modify super admin
Source: CONTROL 4G manual 1.0, page 10

Add users

Adds 1 to 20 numbers, comma separated, with the rights that follow: CLIPn=1 (open channel n by call, monostable channels only), SMSn=1 (open channel n by SMS OUTn), STATUSn=1 (read information input n, inputs 1-3). A right not named is OFF. More than 20 numbers adds none. A number already stored is skipped. A multiple ADD sends no welcome SMS and cannot add administrators.

Syntax: #{pwd},ADD={phones},{rights}
In the manual: #password,ADD=48123456789,48123456789,CLIP1=1,SMS2=1,STATUS1=1
Reply: SUCCESSFULLY ADDED, or OK (n params); ERROR: Already exists; ERROR: Memory full; ERROR: You can specify max. 20 numbers
Source: CONTROL 4G manual 1.0, page 16

Change a user's rights

Sets the named rights (CLIPn, SMSn, STATUSn, INnACT, INnDEACT, VIP) of one stored number; rights not named stay as they are.

Syntax: #{pwd},MOD={phone},{rights}
In the manual: #password,MOD=48123456789,clip1=0,sms1=1
Reply: SUCCESSFULLY MODIFIED, or OK (n params); ERROR: Does not exist; ERROR: No subscribers
Source: CONTROL 4G manual 1.0, page 16

Change the rights of all users

Sets the named rights of every stored number. VIP and administrator-only rights cannot be changed this way. An administrator changes everyone except the super administrator.

Syntax: #{pwd},MODALL,{rights}
In the manual: #password,MODALL,clip1=0,sms1=1
Reply: MODIFIED ALL (super administrator) or MODIFIED ALL EXCEPT SUPERADMIN (administrator)
Source: CONTROL 4G manual 1.0, page 17

Delete a user

Removes one number from the memory.

Syntax: #{pwd},DEL={phone}
In the manual: #password,DEL=48123456789
Reply: SUBSCRIBER DELETED; ERROR: Does not exist
Source: CONTROL 4G manual 1.0, page 17

Delete all administrators

Super administrator only.

Syntax: #{pwd},DELADMINS
In the manual: #password,DELADMINS
Reply: ALL ADMINS DELETED EXCEPT YOU
Source: CONTROL 4G manual 1.0, page 17

Replace a user's number

Changes a stored number and keeps its rights.

Syntax: #{pwd},REP={oldphone},{newphone}
In the manual: #password,REP=48123456789,48987654321
Reply: OK (n params) or an ERROR line
Source: CONTROL 4G manual 1.0, page 17

Delete all users

Removes every stored number.

Syntax: #{pwd},DELALL
In the manual: #password,DELALL
Reply: ALL SUBSCRIBERS DELETED
Source: CONTROL 4G manual 1.0, page 17

Read a user's rights

Returns the settings of one stored number. The manual does not print the reply text.

Syntax: #{pwd},GET={phone}
In the manual: #password,GET=48123456789
Reply: Settings of the number (format not in the manual); ERROR: Does not exist
Source: CONTROL 4G manual 1.0, page 17

Read the receiver settings

Returns control methods, channel modes, input types, reply settings, the number of subscribers and administrators, and the firmware version (Frm = x, page 9). The manual does not print the reply text.

Syntax: #{pwd},GET
In the manual: #password,GET
Reply: Settings summary (format not in the manual)
Source: CONTROL 4G manual 1.0, page 15

Read the channel and input names

Returns the user-friendly names of the outputs and inputs.

Syntax: #{pwd},GETNAMES
In the manual: #password,GETNAMES
Reply: Names (format not in the manual)
Source: CONTROL 4G manual 1.0, page 15

Set the pulse time of channel n

Monostable mode: the relay of channel n (1 or 2) closes for 1-65535 seconds. 0 sets bistable mode (next entry). Channels 3 and 4 of the radio module are fixed at 1 s.

Syntax: #{pwd},TIME{n}={seconds}
In the manual: #password,TIME1=20
Reply: OK (n params)
Source: CONTROL 4G manual 1.0, page 11

Set channel n to bistable

Channel n (1 or 2) stays on until switched off. A bistable channel cannot be opened by call, only by SMS OUTnON / OUTnOFF.

Syntax: #{pwd},TIME{n}=0
In the manual: #password,TIME1=0
Reply: OK (n params)
Source: CONTROL 4G manual 1.0, page 11

Name output n

Channels 1-4, up to 20 characters without diacritics or special signs.

Syntax: #{pwd},NameOUT{n}="{name}"
In the manual: #password,NameOUT1 ="Entrance gate"
Reply: OK (n params)
Source: CONTROL 4G manual 1.0, page 11

Switch channel n off

Channels 1-4. The channel no longer reacts to any control.

Syntax: #{pwd},STOP{n}=1
In the manual: #password,STOP1=1
Reply: OK (n params)
Source: CONTROL 4G manual 1.0, page 11

Switch channel n on

Channels 1-4.

Syntax: #{pwd},STOP{n}=0
In the manual: #password,STOP1=0
Reply: OK (n params)
Source: CONTROL 4G manual 1.0, page 11

Input n normally open

Information inputs 1-3.

Syntax: #{pwd},TYPE{n}=NO
In the manual: #password,TYPE1=NO
Reply: OK (n params)
Source: CONTROL 4G manual 1.0, page 11

Input n normally closed

Information inputs 1-3.

Syntax: #{pwd},TYPE{n}=NC
In the manual: #password,TYPE1=NC
Reply: OK (n params)
Source: CONTROL 4G manual 1.0, page 11

Name input n

Information inputs 1-3, up to 20 characters without diacritics or special signs.

Syntax: #{pwd},NameIn{n}="{name}"
In the manual: #password,NameIn1= "Gate status"
Reply: OK (n params)
Source: CONTROL 4G manual 1.0, page 12

Text when input n turns active

Up to 60 characters. Only administrators receive input notifications. SmsONn="" restores the default text (INn = ON).

Syntax: #{pwd},SmsON{n}="{text}"
In the manual: #password,SmsON1= "Gate open"
Reply: OK (n params)
Source: CONTROL 4G manual 1.0, page 12

Text when input n turns inactive

Up to 60 characters. Only administrators receive input notifications. SmsOFFn="" restores the default text (INn = OFF).

Syntax: #{pwd},SmsOFF{n}="{text}"
In the manual: #password,SmsOFF1= "Gate closed"
Reply: OK (n params)
Source: CONTROL 4G manual 1.0, page 12

Status reply after each control SMS on

After each control SMS the receiver texts the state of its inputs and outputs, instead of OK. On at the factory (page 9).

Syntax: #{pwd},AutoStatus=1
In the manual: #password,AutoStatus=1
Reply: OK (n params)
Source: CONTROL 4G manual 1.0, page 13

Status reply after each control SMS off

No status text after a control SMS.

Syntax: #{pwd},AutoStatus=0
In the manual: #password,AutoStatus=0
Reply: OK (n params)
Source: CONTROL 4G manual 1.0, page 13

OK / ERROR reply after each control SMS on

After each control SMS the receiver texts OK or an ERROR line. Without AutoAck or AutoStatus a control SMS gets no reply.

Syntax: #{pwd},AutoAck=1
In the manual: #password,AutoAck=1
Reply: OK (n params)
Source: CONTROL 4G manual 1.0, page 13

OK / ERROR reply after each control SMS off

No OK / ERROR text after a control SMS.

Syntax: #{pwd},AutoAck=0
In the manual: #password,AutoAck=0
Reply: OK (n params)
Source: CONTROL 4G manual 1.0, page 13

Language of the welcome SMS

PL, EN or DE.

Syntax: #{pwd},LANG={lang}
In the manual: #password,LANG=EN
Reply: OK (n params)
Source: CONTROL 4G manual 1.0, page 13

Welcome SMS to new users on

A user added alone gets an SMS from the receiver with his control methods and a link to DTM's Android widget. On at the factory. Also needed for STATUS and GETCONFIG.

Syntax: #{pwd},UserNotify=1
In the manual: #password,UserNotify=1
Reply: OK (n params)
Source: CONTROL 4G manual 1.0, page 13

Welcome SMS to new users off

No welcome SMS. It also blocks the STATUS and GETCONFIG commands and DTM's status widget.

Syntax: #{pwd},UserNotify=0
In the manual: #password,UserNotify=0
Reply: OK (n params)
Source: CONTROL 4G manual 1.0, page 14

Silent mode on

No reply to configuration SMS; only GET, GETNAMES, GETAUTO and GET=<number> still answer (page 33).

Syntax: #{pwd},Silent=1
In the manual: #password,Silent=1
The manual prints no reply text. It says the mode will "disable SMS to the administrator after the configuration command" (page 14).
Source: CONTROL 4G manual 1.0, page 14

Silent mode off

Configuration SMS are answered again.

Syntax: #{pwd},Silent=0
In the manual: #password,Silent=0
Reply: OK (n params)
Source: CONTROL 4G manual 1.0, page 14

Guests may open channel n by call

Any caller (a number not stored) opens monostable channel n; with ClipPass set, the guest types the code and # after a tone. Of channels 3 and 4 only channel 3 can be called. Off at the factory. Without MOD= this sets the guest right, not a user's.

Syntax: #{pwd},CLIP{n}=1
In the manual: #password,CLIP1=1
Reply: OK (n params)
Source: CONTROL 4G manual 1.0, page 14

Guests may not open channel n by call

Only stored numbers with CLIPn=1 open channel n by call.

Syntax: #{pwd},CLIP{n}=0
In the manual: #password,CLIP1=0
Reply: OK (n params)
Source: CONTROL 4G manual 1.0, page 14

Guests may open channel n by SMS

Any sender may send OUTn (or password.OUTn when SmsPass is set). Guests get no reply SMS.

Syntax: #{pwd},SMS{n}=1
In the manual: #password,SMS1=1
Reply: OK (n params)
Source: CONTROL 4G manual 1.0, page 14

Guests may not open channel n by SMS

Only stored numbers with SMSn=1 open channel n by SMS.

Syntax: #{pwd},SMS{n}=0
In the manual: #password,SMS1=0
Reply: OK (n params)
Source: CONTROL 4G manual 1.0, page 14

Guest code for calls

Digits only, up to 16. ClipPass="" removes it.

Syntax: #{pwd},ClipPass="{code}"
In the manual: #password,ClipPass="123"
Reply: OK (n params)
Source: CONTROL 4G manual 1.0, page 15

Guest password for control SMS

Letters and digits, up to 16. Control SMS then read password.OUTn. SmsPass="" removes it.

Syntax: #{pwd},SmsPass="{code}"
In the manual: #password,SmsPass="abc123"
Reply: OK (n params)
Source: CONTROL 4G manual 1.0, page 15

Factory reset

Restores factory settings and deletes every stored number; the password is admin again. Holding RESET for 8 seconds does the same (page 8).

Syntax: #{pwd},Format=0417
In the manual: #password,Format=0417
Reply: DATA CLEANED
Source: CONTROL 4G manual 1.0, page 16

Automatic adding on

For up to 48 hours, every number that texts the 4-digit PIN to the receiver is stored with the given rights.

Syntax: #{pwd},AUTOADD={pin},time={hours},{rights}
In the manual: #password,AUTOADD=1234,time=12,clip1=1,sms1=1,status1=1
Reply: AUTOADD ON (with details)
Source: CONTROL 4G manual 1.0, page 19

Automatic adding off

Ends the automatic adding mode.

Syntax: #{pwd},AUTOADD=0
In the manual: #password,AUTOADD=0
Reply: AUTOADD OFF
Source: CONTROL 4G manual 1.0, page 19

Read the automatic adding settings

Returns the automatic adding mode settings.

Syntax: #{pwd},GETAUTO
In the manual: #password,GETAUTO
Reply: Settings (format not in the manual)
Source: CONTROL 4G manual 1.0, page 19

Open channel n by SMS

Sent from a stored number with SMSn=1. Channels 1-4, monostable mode. Case does not matter (the manual's announcements use out1). The SMS is charged at the operator's rate.

Syntax: OUT{n}
In the manual: OUT1
Reply: OK only with AutoAck=1; the status text with AutoStatus=1; ERROR: Command not available without the right
Source: CONTROL 4G manual 1.0, page 30

Switch bistable channel n on

Channels 1 and 2 in bistable mode (TIMEn=0) only.

Syntax: OUT{n}ON
In the manual: OUT1ON
Reply: OK only with AutoAck=1; the status text with AutoStatus=1
Source: CONTROL 4G manual 1.0, page 30

Switch bistable channel n off

Channels 1 and 2 in bistable mode (TIMEn=0) only.

Syntax: OUT{n}OFF
In the manual: OUT1OFF
Reply: OK only with AutoAck=1; the status text with AutoStatus=1
Source: CONTROL 4G manual 1.0, page 30

Status of inputs and outputs

The reply shows only what the sender's rights allow. Does not work with UserNotify=0. The manual does not print the reply text.

Syntax: STATUS
In the manual: STATUS
Reply: Status text (format not in the manual)
Source: CONTROL 4G manual 1.0, page 30

My control methods

Lists the control methods the sender has. Does not work with UserNotify=0.

Syntax: GETCONFIG
In the manual: GETCONFIG
Reply: Control methods text (format not in the manual)
Source: CONTROL 4G manual 1.0, page 30

Control SMS with an SMS password

When an SMS control password (SmsPass) is set, the control command follows the password and a dot.

Syntax: {smspwd}.{command}
In the manual: abc123.out1
Reply: As the command itself
Source: CONTROL 4G manual 1.0, page 30

Modules the app supports

The modules the app works with are on the supported hardware page. Their manuals are on the manuals page.